https://doi.org/10.4081/jae.2022.1388
Development and performance evaluation of an oil palm harvesting robot for the elimination of ergonomic risks associated with oil palm harvesting
Published: 9 September 2022
Abstract Views: 1299
PDF: 743
HTML: 355
HTML: 355
Publisher's note
All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article or claim that may be made by its manufacturer is not guaranteed or endorsed by the publisher.
All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article or claim that may be made by its manufacturer is not guaranteed or endorsed by the publisher.
Authors
This study was aimed at developing and evaluating the performance of an oil palm fresh fruit bunch harvesting robot that will eliminate the possible risks associated with oil palm harvesting. The result of this study showed that the average height of oil palm trees in the study area was 5.531 m, which shows the unsuitability of the existing traditional methods in the harvesting process. This study also used a geared DC motor to develop an oil palm harvester, solving the stability issue encountered by previous researchers during the harvesting process without necessarily reducing the climbing speed by a wide margin. In addition, the use of geared DC motor help in the production of high torque for the climbing process, and due to this high torque, instability during the harvesting process was reduced.
Akande F., Oriola K., Oniya O., Bolaji G. 2013. Level of oil palm production mechanization in selected local government areas of Oyo and Osun states, Nigeria. Innov. Syst. Des. Engine. 4:36-40.
Bankole A.S., Ojo S.O., Olutumise A.I., Garba I.D., Abdulqadir M.I. 2018. Efficiency evaluation of small holders palm oil production in Edo State, Nigeria. Asian J. Agric. Extens. Econ. Soc. 1-9.
DOI: https://doi.org/10.9734/AJAEES/2018/40850
Bronkhorst E., Cavallo E., van Dorth tot Medler M., Klinghammer S., Smit H.H., Gijsenbergh A., van der Laan C. 2017. Current practices and innovations in smallholder palm oil finance in Indonesia and Malaysia: long-term financing solutions to promote sustainable supply chains. CIFOR Occasional Paper No. 177. Center for International Forestry Research (CIFOR), Bogor, Indonesia.
Chinchkar D., Gajghate S., Panchal R., Shetenawar R., Mulik, P. 2017. Design of Rocker Bogie mechanism. Int. Adv. Res. J. Sci. Engine. Technol. 4:46-50.
DOI: https://doi.org/10.17148/IARJSET/NCDMETE.2017.13
Cotta A., Devidas N.T., Ekoskar V.K. 2016. Wireless communication using HC-05 Bluetooth module interfaced with Arduino. Int. J. Sci. Engine. Technol. Res. 5:4.
Feldpausch T.R., Banin L., Phillips O.L., Baker T.R., Lewis S.L., Quesada C.A., Affum-Baffoe K. 2011. Height-diameter allometry of tropical forest trees. Biogeosci. 8:1081-106.
DOI: https://doi.org/10.5194/bg-8-1081-2011
Gold I.L., Ikuenobe C.E., Asemota O., Okiy D.A. 2012. Palm and palm kernel oil production and processing in Nigeria. pp. 275-298 in Palm oil, AOCS Press.
DOI: https://doi.org/10.1016/B978-0-9818936-9-3.50013-7
Jelani A.R., Ahmad D., Hitam A., Yahya A., Jamak J. 1998. Force and energy requirements for cutting oil palm frond. J. Oil Palm Res. 10:10-24.
Juman M.A., Wong Y.W., Rajkumar R.K., Goh L.J. 2016. A novel tree trunk detection method for oil-palm plantation navigation. Comput. Electron. Agric. 128:172-80.
DOI: https://doi.org/10.1016/j.compag.2016.09.002
Keramat J., Jafari A., Rafiee S., Mohtsebi S. 2007. A survey on some physical properties of the Date Palm tree. J. Agric. Technol. 3:317-22.
Khurmi R., Gupta J. 2006. Theory of machines. Eurasia Publishing House (PVT) Ltd., New Delhi, India.
Kuwamura H. 2011. Coefficient of friction between wood and steel under heavy contact. J. Str. Cons. Eng. 76:1469-78.
DOI: https://doi.org/10.3130/aijs.76.1469
Lam T.L., Xu Y. 2012. Tree climbing robot: design, kinematics and motion planning (Vol. 78). Springer, Berlin, Germany.
DOI: https://doi.org/10.1007/978-3-642-28311-6
Maluin F.N., Hussein M.Z., Idris A.S. 2020. An overview of the oil palm industry: challenges and some emerging opportunities for nanotechnology development. Agron. J. 10:356.
DOI: https://doi.org/10.3390/agronomy10030356
Myzabella N., Fritschi L., Merdith N., El-Zaemey S., Chih H., Reid A. 2019. Occupational health and safety in the palm oil industry: a systematic review. Int. J. Occup. Environ. Med. 10:159.
DOI: https://doi.org/10.15171/ijoem.2019.1576
Othman N., Jaffar M., Ahmad H., Hasnum M. (2018). Development and localization of a mobile robot. pp. 121-122 in Proceedings of Mechanical Engineering Research Day 2018. Centre for Advanced Research on Energy, Faculty of Mechanical Engineering, Universiti Teknik, Malaysia.
Oyedeji A.N., Umar U.A., Kuburi L.S. 2021. Investigation of the allometry of oil palm trees in Nigeria for mechanization of the farming process. ATBU J. Sci. Technol. Educ. 9:123-30.
Oyedeji A., Umar A., Kuburi L., Apeh I. 2020. Trend of harvesting of oil palm fruit; the mechanisms, and challenges. Int. J. Sci. Res. Engine. Develop. 3:1053-63.
Pengfei G., Liquiong T., Subhas M. 2018. A novel robotic tree climbing mechanism with anti-falling functionality for tree pruning. J. Mech. Robot. 10:1-8.
Prasad A., Varghese T., Varghese T.T., Skariah E.N. 2016. Wireless palm tree harvester. Int. J. Adv. Res. Ele. Ele. Ins. Eng. 5:122-6.
Praveenbabu R., Sneha S., Pavan Kumar S., Yuvaraj R., Sanjay M. 2017. Tree climbing robot. Int. J. Innov. Emer. Res. Eng. 86-90.
Roser M., Appel C., Ritchie H. 2020. Human height. Available from: https://ourworldindata.org/human-height Accessed: January 31, 2020.
Saeed O.M.B., Sankaran S., Shariff A.R.M., Shafri H.Z.M., Ehsani R., Alfatni M.S., Hazir M.H.M. 2012. Classification of oil palm fresh fruit bunches based on their maturity using portable four-band sensor system. Comput. Electron. Agr. 82:55-60.
DOI: https://doi.org/10.1016/j.compag.2011.12.010
Tan K.P., Kanniah K.D., Cracknell A.P. 2014. On the upstream inputs into the MODIS primary productivity products using biometric data from oil palm plantations. Int. J. Remote Sens. 35:2215-46.
DOI: https://doi.org/10.1080/01431161.2014.889865
Vijay V., Pimm S.L., Jenkins C.N., Smith S.J. 2016. The impacts of oil palm on recent deforestation and biodiversity loss. PLoS One. 11:e0159668.
DOI: https://doi.org/10.1371/journal.pone.0159668
How to Cite
Oyedeji, A. N. (2022) “Development and performance evaluation of an oil palm harvesting robot for the elimination of ergonomic risks associated with oil palm harvesting”, Journal of Agricultural Engineering, 53(3). doi: 10.4081/jae.2022.1388.
Copyright (c) 2022 the Author(s)
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
PAGEPress has chosen to apply the Creative Commons Attribution NonCommercial 4.0 International License (CC BY-NC 4.0) to all manuscripts to be published.
Similar Articles
- Rita Papa, Giuseppe Manetto, Emanuele Cerruto, Sabina Failla, Mechanical distribution of beneficial arthropods in greenhouse and open field: A review , Journal of Agricultural Engineering: Vol. 49 No. 2 (2018)
- Francesco Barreca, Pasquale Praticò, Giuseppe Davide Cardinali, A low-energy storage container for food and agriculture products , Journal of Agricultural Engineering: Vol. 52 No. 3 (2021)
- Francesca Valenti, Simona M.C. Porto, Giovanni Cascone, Claudia Arcidiacono, Potential biogas production from agricultural by-products in Sicily. A case study of citrus pulp and olive pomace , Journal of Agricultural Engineering: Vol. 48 No. 4 (2017)
- Maria Lisa Clodoveo, An overview of emerging techniques in virgin olive oil extraction process: strategies in the development of innovative plants , Journal of Agricultural Engineering: Vol. 44 No. s2 (2013): Proceedings of the 10th Conference of the Italian Society of Agricultural Engineering
- Serafina Andiloro, Giuseppe Bombino, Vincenzo Tamburino, Demetrio Antonio Zema, Santo Marcello Zimbone, Aerated lagooning of agro-industrial wastewater: depuration performance and energy requirements , Journal of Agricultural Engineering: Vol. 44 No. s2 (2013): Proceedings of the 10th Conference of the Italian Society of Agricultural Engineering
- Marco Daou, Rocco Furferi, Lucia Recchia, Enrico Cini, A MODELLING APPROACH TO EXTRA VIRGIN OLIVE OIL EXTRACTION , Journal of Agricultural Engineering: Vol. 38 No. 4 (2007)
- Roberto Romaniello, Alessandro Leone, Giorgio Peri, Measurement of food colour in L*a*b* units from RGB digital image using least squares support vector machine regression , Journal of Agricultural Engineering: Vol. 46 No. 4 (2015)
- Elio Dinuccio, Fabrizio Gioelli, Dalibor Cuk, Luca Rollè, Paolo Balsari, The use of co-digested solid fraction as feedstock for biogas plants , Journal of Agricultural Engineering: Vol. 44 No. 4 (2013)
- Lucia Recchia, Daniele Sarri, Marco Rimediotti, Paolo Boncinelli, Enrico Cini, Marco Vieri, Towards the environmental sustainability assessment for the viticulture , Journal of Agricultural Engineering: Vol. 49 No. 1 (2018)
- Adeshina Fadeyibi, Zinash D. Osunde, Evans C. Egwim, Peter A. Idah, Performance evaluation of cassava starch-zinc nanocomposite film for tomatoes packaging , Journal of Agricultural Engineering: Vol. 48 No. 3 (2017)
<< < 3 4 5 6 7 8 9 10 11 12 > >>
You may also start an advanced similarity search for this article.
