https://doi.org/10.4081/jae.2023.1543
Theoretical analysis and experiment of seed-picking mechanism of belt high-speed seed-guiding device for corn
Published: 30 October 2023
Abstract Views: 551
PDF: 164
HTML: 2
HTML: 2
Publisher's note
All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article or claim that may be made by its manufacturer is not guaranteed or endorsed by the publisher.
All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article or claim that may be made by its manufacturer is not guaranteed or endorsed by the publisher.
Authors
Under the condition of high-speed sowing (12-16 km/h), due to the high rotational speeds of the seed disk, the seeds leave the disk at an excessively high speed, which challenges the seed-picking capacity of the belt-type high-speed seed guide device. In this paper, the theory of seed-picking mech-anism is analyzed, and performance optimization tests are completed to further improve the operation effect of the seeder. The mechanical model of seed picking was established through the force analysis of seeds. The influence of vacuum degree, feeder wheel rotation speed, and seed picking angle on seed picking quality and the parameter range of each factor were obtained by single factor test. A three-factor five-level quadratic orthogonal rotation combination test was performed, and the test re-sults were refined and evaluated. The test factors used were vacuum degree, feeder wheel rotation speed, and seed picking angle. The test indexes used were the seed picking rate, re-picking rate, and miss-picking rate. According to the results, the seed picking rate was 99.89%, the re-picking rate was 0, and the miss-picking rate was 0.11% when the vacuum degree was 6.89 KPa, the feeder wheel rotation speed was 568.95 rpm, and the seed picking angle was 7.6°.
Badua, S.A., Sharda, A., Strasser, R., Ciampitti, I. (2021). Ground speed and planter downforce in-fluence on corn seed spacing and depth. Precis. Agric. 22, 1154–1170.
DOI: https://doi.org/10.1007/s11119-020-09775-7
Hanna, H. M., Steward, B. L., & Aldinger, L. (2010). Soil loading effects of planter depth-gauge wheels on early corn growth. Applied Engineering in Agriculture, 6(4), 551–556.
DOI: https://doi.org/10.13031/2013.32058
Garner E. B., Thiemke D. B., Rylander D.J. et al. (2016). Seeding machine with seed deliver system [P]. United States patent, US 9480199 B2, Nov.1, 2016.
Garner E., Friestad M.E., Mariman N.A, et al. (2010). Seed delivery apparatus with sensor and mov-ing member to capture and move seed to a lower outlet opening [P]. United States patent, US2010/0192821, Aug.5, 2010.
Jinqing, L., Ying, Y., Zihui, L., Qinqin, S., Jicheng, L., & Zhongyuan, L. (2016). Design and experi-ment of an air-suction potato seed metering device. International Journal of Agricultural and Bio-logical Engineering, 9, 33-42.
Jinwu, W., Han, T., Jinfeng, W., Xin, L., & Huinan, H. (2017). Optimization design and experiment on ripple surface type pickup finger of precision maize seed metering device. International Journal of Agricultural and Biological Engineering, 10, 61-71.
Kaixing, Z., Yuanyuan, S., Lei, L.H., Xianxi, L., & Xiuyan, Z. (2020). Design and test of variable diameter pneumatic drum type bean seed metering device. INMATEH-Agricultural Engineering, 60, 9-18.
DOI: https://doi.org/10.35633/inmateh-60-01
Kocher, M.F., Coleman, J.M., Smith, J.A., & Kachman, S.D. (2011). Corn seed spacing uniformity as affected by seed tube condition. Applied Engineering in Agriculture, 27, 177-183.
DOI: https://doi.org/10.13031/2013.36484
Li, Y., Xing, S., Li, S., Li, L., Zhang, X., Song, Z., & Li, F. (2020). Seeding performance simulations and experiments for a spoon-wheel type precision cottonseed-metering device based on EDEM. Mechanical Engineering Science. https://doi.org/10.33142/mes.v2i1.2615
DOI: https://doi.org/10.33142/mes.v2i1.2615
Liu, F., Lin, Z., Li, D., & Zhang, T. (2021). Design optimization and performance test of magnetic pickup finger seed metering device. INMATEH-Agricultural Engineering, 137-144.
DOI: https://doi.org/10.35633/inmateh-63-14
Liu, K, Shujuan Y. (2019). Design and experiment of seeding performance monitoring system for suction corn planter. International Journal of Agricultural and Biological Engineering, 97-103.
DOI: https://doi.org/10.25165/j.ijabe.20191204.4185
Liu, W., Hu, J., Zhao, X., Pan, H., Lakhiar, I.A., & Wang, W. (2019). Development and experimental analysis of an intelligent sensor for monitoring seed flow rate based on a seed flow reconstruction technique. Comput. Electron. Agric., 164.
DOI: https://doi.org/10.1016/j.compag.2019.104899
Mapoka, K.O., Birrell, S.J., & Tekeste, M.Z. (2019). A comprehensive survey of nondestructive sens-ing technologies for the detection of corn seeds in a closed trench and measuring planting depth to augment the conventional method. Comput. Electron. Agric., 249-257.
DOI: https://doi.org/10.1016/j.compag.2019.02.010
Patel, S., Bhimani, J.B., Gupta, P., & Yaduvanshi, B.K. (2019). Optimization of the operational pa-rameters of a picking-type pneumatic planter using response surface methodology. Journal of AgriSearch. https://doi.org/10.21921/JAS.V6I1.14919
DOI: https://doi.org/10.21921/jas.v6i1.14919
Qi, N., Caiyun, L., Hongwen, L., Qingjie, W., Hongnan, H., Zhongcai, W., & Hongbo, Z. (2018). Development of artificial neural network models for seeding performance of a belt-type corn seed metering device. https://doi.org/10.13031/AIM.201800371
DOI: https://doi.org/10.13031/aim.201800371
Sauder G.A., Dill K.R., Dunlap D. L., et al. (2002). Apparatus and method for controlled delivery of seed to an open furrow[P]. United States patent, US 6681706B2, Feb. 26,2002.
Wang, J., Qi, X., Xu, C., Wang, Z., Jiang, Y., & Tang, H. (2021). Design evaluation and performance analysis of the inside-filling air-assisted high-speed precision maize seed-metering device. Sus-tainability, 13, 5483.
DOI: https://doi.org/10.3390/su13105483
Xiong, D., Wu, M., Wei, X., Liu, R., & Luo, H. (2021). Design and experimental study of the general mechanical pneumatic combined seed metering device. Applied Sciences. https://doi.org/10.3390/app11167223
DOI: https://doi.org/10.3390/app11167223
Xu, P., You, Y., Wang, D., Sun, X., Lv, J., Ma, W., Zhang, X., Ma, Z., & Lin, H. (2020). Optimized design of cone-hole wheel type seed metering device based on EDEM. https://doi.org/10.13031/aim.202000501.
DOI: https://doi.org/10.13031/aim.202000501
How to Cite
Ma, C. (2023) “Theoretical analysis and experiment of seed-picking mechanism of belt high-speed seed-guiding device for corn”, Journal of Agricultural Engineering, 55(1). doi: 10.4081/jae.2023.1543.
Copyright (c) 2023 the Author(s)
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
PAGEPress has chosen to apply the Creative Commons Attribution NonCommercial 4.0 International License (CC BY-NC 4.0) to all manuscripts to be published.
Similar Articles
- Yusuf Uzun, Mehmet Resit Tolun, Halil Tanyer Eyyuboglu, Filiz Sarı, An intelligent system for detecting Mediterranean fruit fly [Medfly; Ceratitis capitata (Wiedemann)] , Journal of Agricultural Engineering: Vol. 53 No. 3 (2022)
- Daniele Masseroni, Jasim Uddin, Reece Tyrrell, Iven Mareels, Claudio Gandolfi, Arianna Facchi, Towards a smart automated surface irrigation management in rice-growing areas in Italy , Journal of Agricultural Engineering: Vol. 48 No. 1 (2017)
- Sergio Castellano, Giuseppe Starace, Lorenzo De Pascalis, Marco Lippolis, Giacomo Scarascia-Mugnozza, Experimental results on air permeability of agricultural nets , Journal of Agricultural Engineering: Vol. 47 No. 3 (2016)
- Roberto Beghi, Valentina Giovenzana, Raffaele Civelli, Enrico Cini, Riccardo Guidetti, Characterisation of olive fruit for the milling process by using visible/near infrared spectroscopy , Journal of Agricultural Engineering: Vol. 44 No. 2 (2013)
- Daniele Duca, Giovanni Riva, Ester Foppa Pedretti, Giuseppe Toscano, Chiara Mengarelli, Giorgio Rossini, Solid biofuels production from agricultural residues and processing by-products by means of torrefaction treatment: the case of sunflower chain , Journal of Agricultural Engineering: Vol. 45 No. 3 (2014)
- Juan Ãngel Mintegui Aguirre, José Carlos Robredo Sánchez, Carlos de Gonzalo Aranoa, Pablo Huelin Rueda, Jorge Fallas, Felipe Cisneros, Pedro Cisneros, Adriana Urciuolo, Rodolfo Iturraspe, Forest use strategies in watershed management and restoration: application to three small mountain watersheds in Latin America , Journal of Agricultural Engineering: Vol. 45 No. 1 (2014)
- Giuseppe Ruggiero, Stefano Dal Sasso, Rosa Viviana Loisi, Giuseppe Verdiani, Characteristics and distribution of trulli constructions in the area of the site of community importance Murgia of Trulli , Journal of Agricultural Engineering: Vol. 44 No. 2 (2013)
- Roberto Romaniello, Antonietta Eliana Barrasso, Antonio Berardi, Claudio Perone, Antonia Tamborrino, Filippo Catalano, Antonietta Baiano, Hyperspectral imaging system to online monitoring the soy flour content in a functional pasta , Journal of Agricultural Engineering: Vol. 54 No. 4 (2023)
- Ian Torotwa, Qishuo Ding, Emmanuel Awuah, Ruiyin He, Biomimetic tool design improves tillage efficiency, seedbed quality, and straw incorporation during rototilling in conservation farming , Journal of Agricultural Engineering: Vol. 54 No. 1 (2023)
- Silvana Fuina, Giuseppe C. Marano, Giuseppe Puglisi, Domenico De Tommasi, Giacomo Scarascia-Mugnozza, Thermo-mechanical response of rigid plastic laminates for greenhouse covering , Journal of Agricultural Engineering: Vol. 47 No. 3 (2016)
<< < 11 12 13 14 15 16 17 18 19 20 > >>
You may also start an advanced similarity search for this article.
