https://doi.org/10.4081/jae.2023.1543
Theoretical analysis and experiment of seed-picking mechanism of belt high-speed seed-guiding device for corn
Published: 30 October 2023
Abstract Views: 551
PDF: 164
HTML: 2
HTML: 2
Publisher's note
All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article or claim that may be made by its manufacturer is not guaranteed or endorsed by the publisher.
All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article or claim that may be made by its manufacturer is not guaranteed or endorsed by the publisher.
Authors
Under the condition of high-speed sowing (12-16 km/h), due to the high rotational speeds of the seed disk, the seeds leave the disk at an excessively high speed, which challenges the seed-picking capacity of the belt-type high-speed seed guide device. In this paper, the theory of seed-picking mech-anism is analyzed, and performance optimization tests are completed to further improve the operation effect of the seeder. The mechanical model of seed picking was established through the force analysis of seeds. The influence of vacuum degree, feeder wheel rotation speed, and seed picking angle on seed picking quality and the parameter range of each factor were obtained by single factor test. A three-factor five-level quadratic orthogonal rotation combination test was performed, and the test re-sults were refined and evaluated. The test factors used were vacuum degree, feeder wheel rotation speed, and seed picking angle. The test indexes used were the seed picking rate, re-picking rate, and miss-picking rate. According to the results, the seed picking rate was 99.89%, the re-picking rate was 0, and the miss-picking rate was 0.11% when the vacuum degree was 6.89 KPa, the feeder wheel rotation speed was 568.95 rpm, and the seed picking angle was 7.6°.
Badua, S.A., Sharda, A., Strasser, R., Ciampitti, I. (2021). Ground speed and planter downforce in-fluence on corn seed spacing and depth. Precis. Agric. 22, 1154–1170.
DOI: https://doi.org/10.1007/s11119-020-09775-7
Hanna, H. M., Steward, B. L., & Aldinger, L. (2010). Soil loading effects of planter depth-gauge wheels on early corn growth. Applied Engineering in Agriculture, 6(4), 551–556.
DOI: https://doi.org/10.13031/2013.32058
Garner E. B., Thiemke D. B., Rylander D.J. et al. (2016). Seeding machine with seed deliver system [P]. United States patent, US 9480199 B2, Nov.1, 2016.
Garner E., Friestad M.E., Mariman N.A, et al. (2010). Seed delivery apparatus with sensor and mov-ing member to capture and move seed to a lower outlet opening [P]. United States patent, US2010/0192821, Aug.5, 2010.
Jinqing, L., Ying, Y., Zihui, L., Qinqin, S., Jicheng, L., & Zhongyuan, L. (2016). Design and experi-ment of an air-suction potato seed metering device. International Journal of Agricultural and Bio-logical Engineering, 9, 33-42.
Jinwu, W., Han, T., Jinfeng, W., Xin, L., & Huinan, H. (2017). Optimization design and experiment on ripple surface type pickup finger of precision maize seed metering device. International Journal of Agricultural and Biological Engineering, 10, 61-71.
Kaixing, Z., Yuanyuan, S., Lei, L.H., Xianxi, L., & Xiuyan, Z. (2020). Design and test of variable diameter pneumatic drum type bean seed metering device. INMATEH-Agricultural Engineering, 60, 9-18.
DOI: https://doi.org/10.35633/inmateh-60-01
Kocher, M.F., Coleman, J.M., Smith, J.A., & Kachman, S.D. (2011). Corn seed spacing uniformity as affected by seed tube condition. Applied Engineering in Agriculture, 27, 177-183.
DOI: https://doi.org/10.13031/2013.36484
Li, Y., Xing, S., Li, S., Li, L., Zhang, X., Song, Z., & Li, F. (2020). Seeding performance simulations and experiments for a spoon-wheel type precision cottonseed-metering device based on EDEM. Mechanical Engineering Science. https://doi.org/10.33142/mes.v2i1.2615
DOI: https://doi.org/10.33142/mes.v2i1.2615
Liu, F., Lin, Z., Li, D., & Zhang, T. (2021). Design optimization and performance test of magnetic pickup finger seed metering device. INMATEH-Agricultural Engineering, 137-144.
DOI: https://doi.org/10.35633/inmateh-63-14
Liu, K, Shujuan Y. (2019). Design and experiment of seeding performance monitoring system for suction corn planter. International Journal of Agricultural and Biological Engineering, 97-103.
DOI: https://doi.org/10.25165/j.ijabe.20191204.4185
Liu, W., Hu, J., Zhao, X., Pan, H., Lakhiar, I.A., & Wang, W. (2019). Development and experimental analysis of an intelligent sensor for monitoring seed flow rate based on a seed flow reconstruction technique. Comput. Electron. Agric., 164.
DOI: https://doi.org/10.1016/j.compag.2019.104899
Mapoka, K.O., Birrell, S.J., & Tekeste, M.Z. (2019). A comprehensive survey of nondestructive sens-ing technologies for the detection of corn seeds in a closed trench and measuring planting depth to augment the conventional method. Comput. Electron. Agric., 249-257.
DOI: https://doi.org/10.1016/j.compag.2019.02.010
Patel, S., Bhimani, J.B., Gupta, P., & Yaduvanshi, B.K. (2019). Optimization of the operational pa-rameters of a picking-type pneumatic planter using response surface methodology. Journal of AgriSearch. https://doi.org/10.21921/JAS.V6I1.14919
DOI: https://doi.org/10.21921/jas.v6i1.14919
Qi, N., Caiyun, L., Hongwen, L., Qingjie, W., Hongnan, H., Zhongcai, W., & Hongbo, Z. (2018). Development of artificial neural network models for seeding performance of a belt-type corn seed metering device. https://doi.org/10.13031/AIM.201800371
DOI: https://doi.org/10.13031/aim.201800371
Sauder G.A., Dill K.R., Dunlap D. L., et al. (2002). Apparatus and method for controlled delivery of seed to an open furrow[P]. United States patent, US 6681706B2, Feb. 26,2002.
Wang, J., Qi, X., Xu, C., Wang, Z., Jiang, Y., & Tang, H. (2021). Design evaluation and performance analysis of the inside-filling air-assisted high-speed precision maize seed-metering device. Sus-tainability, 13, 5483.
DOI: https://doi.org/10.3390/su13105483
Xiong, D., Wu, M., Wei, X., Liu, R., & Luo, H. (2021). Design and experimental study of the general mechanical pneumatic combined seed metering device. Applied Sciences. https://doi.org/10.3390/app11167223
DOI: https://doi.org/10.3390/app11167223
Xu, P., You, Y., Wang, D., Sun, X., Lv, J., Ma, W., Zhang, X., Ma, Z., & Lin, H. (2020). Optimized design of cone-hole wheel type seed metering device based on EDEM. https://doi.org/10.13031/aim.202000501.
DOI: https://doi.org/10.13031/aim.202000501
How to Cite
Ma, C. (2023) “Theoretical analysis and experiment of seed-picking mechanism of belt high-speed seed-guiding device for corn”, Journal of Agricultural Engineering, 55(1). doi: 10.4081/jae.2023.1543.
Copyright (c) 2023 the Author(s)
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
PAGEPress has chosen to apply the Creative Commons Attribution NonCommercial 4.0 International License (CC BY-NC 4.0) to all manuscripts to be published.
Similar Articles
- Gabriel Kaless, Johnny Moretto, Fabio Delai, Luca Mao, Mario A. Lenzi, A 2D hydrodynamic-sedimentological model for gravel bed rivers. Part II, Case study: the Brenta River in Italy , Journal of Agricultural Engineering: Vol. 44 No. s2 (2013): Proceedings of the 10th Conference of the Italian Society of Agricultural Engineering
- Giovannni Molari, Michele Mattetti, Daniela Perozzi, Eugenio Sereni, Monitoring of the tractor working parameters from the CAN-Bus , Journal of Agricultural Engineering: Vol. 44 No. s2 (2013): Proceedings of the 10th Conference of the Italian Society of Agricultural Engineering
- Serafina Andiloro, Giuseppe Bombino, Vincenzo Tamburino, Demetrio Antonio Zema, Santo Marcello Zimbone, Aerated lagooning of agro-industrial wastewater: depuration performance and energy requirements , Journal of Agricultural Engineering: Vol. 44 No. s2 (2013): Proceedings of the 10th Conference of the Italian Society of Agricultural Engineering
- G. Sperandio, M. Fedrizzi, M. Iacurto, F. Vincenti, M. Guerrieri, D. Pochi, R. Fanigliulo, M. Pagano, Enhancement of Palm residues (Phoenix canariensis) for a potential use in ruminant feed , Journal of Agricultural Engineering: Vol. 44 No. s2 (2013): Proceedings of the 10th Conference of the Italian Society of Agricultural Engineering
- Paolo Balsari, Paolo Marucco, Claudio Bozzer, Mario Tamagnone, Study of a test methodology to assess potential drift generated by air-assisted sprayers , Journal of Agricultural Engineering: Vol. 44 No. s2 (2013): Proceedings of the 10th Conference of the Italian Society of Agricultural Engineering
- Alessia Tonon, Lorenzo Picco, Diego Ravazzolo, Mario Aristide Lenzi, Using a terrestrial laser scanner to detect wood characteristics in gravel-bed rivers , Journal of Agricultural Engineering: Vol. 45 No. 4 (2014)
- Emanuele Cerruto, Giuseppe Emma, Giuseppe Manetto, SPRAY APPLICATIONS TO TOMATO PLANTS IN GREENHOUSES. PART 2: EFFECT OF SPRAY LANCE TYPE , Journal of Agricultural Engineering: Vol. 40 No. 3 (2009)
- Giacomo Costagli, The use of disc stack centrifuge in the virgin olive oil industry , Journal of Agricultural Engineering: Vol. 49 No. 2 (2018)
- Biagio Bianchi, Antonia Tamborrino, Francesco Santoro, Assessment of the energy and separation efficiency of the decanter centrifuge with regulation capability of oil water ring in the industrial process line using a continuous method , Journal of Agricultural Engineering: Vol. 44 No. s2 (2013): Proceedings of the 10th Conference of the Italian Society of Agricultural Engineering
- Alessio Mencarelli, Raffaele Cavalli, Rosa Greco, Analysis of the main physical and chemical characteristics of the vine shoots of three vine varieties from Veneto (Italy) , Journal of Agricultural Engineering: Vol. 53 No. 4 (2022)
<< < 25 26 27 28 29 30 31 32 33 34 > >>
You may also start an advanced similarity search for this article.
