https://doi.org/10.4081/jae.2023.1546
Design and experiment of furrow side pick-up soil blade for wheat strip-till planter using the discrete element method
Published: 30 October 2023
Abstract Views: 751
PDF: 229
HTML: 5
HTML: 5
Publisher's note
All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article or claim that may be made by its manufacturer is not guaranteed or endorsed by the publisher.
All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article or claim that may be made by its manufacturer is not guaranteed or endorsed by the publisher.
Authors
The strip rotary tillage method effectively reduces the occurrence of straw clogging and creates a favorable seed bed environment. However, the mixture of crushed straw and soil in the seeding area results in inadequate seed-soil contact following compaction by the press wheels. A chisel-type opener furrow side pick-up blade was proposed to improve seed-soil contact by picking up wet soil from the furrow’s side. The discrete element method was used to investigate the impact of earth blade surface parameters on soil dynamics. The key factors of the blade, including forward velocity, endpoint tangent angle, and angle of soil entry, were determined through theoretical analysis. Soil cover thickness and straw ratio in the seed furrow were evaluated using orthogonal rotation regression tests. The results show that the endpoint tangent angle and angle of soil entry have the greatest influence on soil cover thickness, while the angle of soil entry has the greatest influence on the straw ratio. The optimal values for the forward velocity, endpoint tangent angle, and angle of soil entry are 4.86 km/h, 107.17°, and 5.46°, respectively, resulting in a soil cover thickness of 40 mm and a straw ratio of 21.46%. Confirmatory soil bin tests showed similar results, with a soil cover thickness of 40.4 mm and a straw ratio of 18.03%. These results provide a viable solution for improving seed-soil contact after strip rotary tillage planter seeding.
Aikins K.A., Barr J., Ucgul M., Jensen T., Antille D.L., Desbiolles J.M.A. 2020. No-tillage furrow opener performance: A review of tool geometry, settings and interactions with soil and crop residue. Soil Res. 58:603-21.
Bai L., Huang Y., Gao P., Ding S., Zhang H., Fu Z., Zhu R. 2020. Design and test of seed and fertilizer separate device based on double disc covering soil. J. Northwest A & F University (Natural Science Edition). 1:135-45+154.
Barker M.E., Plouffe C. 2017. Simulation of Planter Row Cleaner in Corn Residue Using Discrete Element Modeling. ASABE Annual International Meeting (p. 1).
Chandio F.A. 2013. Interaction of straw-soil-disc tool under controlled conditions. Unpublished thesis (PhD), of Nanjing Agricultural University, China.
Chen H., Hou L., Hou S., Li Y., Min S., Chai Y. 2018. Design and Optimization Experiment of Anti-blocking Mechanism of Notillage Planter for Grand Ridge with Raw Corn Stubble. Trans. Chin. Soc. Agric. Machin. 8:59-67.
Ding Q., Ren J., Belal E.A., Zhao J., Ge S., Li Y. 2017. DEM Analysis of Subsoiling Process in Wet Clayey Paddy Soil. Trans. Chin. Soc. Agric. Machin. 3:38-48.
Fu S.Y., Feng X.Q., Lauke B., Mai Y.W. 2008. Effects of particle size, particle/matrix interface adhesion and particle loading on mechanical properties of particulate–polymer composites. Compos. B. Eng. 39:933-61.
Gu F., Hu Z., Chen Y., Wu F. 2016. Development and experiment of peanut no-till planter under full wheat straw mulching based on “clean area planting”. Trans. Chin. Soc. Agric. Eng. 20:15-23.
Itasca C.G.I. 2005. PFC3D (Particle Flow Code in Three Dimensions). Minneapolis, Minnesota, USA.
Liu F., Jian Z., Chen J. 2018a. Modeling of flexible wheat straw by discrete element method and its parameter calibration. Int. J. Agric. Biol. Eng. 11:42-6.
Liu J., Wang H., Wang Q., Li S., Li H., He J. 2018b. Design and experiment of strip cleaning device of no and minimum tillage corn seeder. Transact. CSAM. 49:132-40.
Liu F., Zhang J., Li B., Chen J. 2016. Calibration of parameters of wheat required in Discrete Element Method simulation based on repose angle of particle heap. Trans. Chin. Soc. Agric. Eng. 12:247-53.
Liu X., Zhang Q., Liu L., Wei G., Xiao W., Liao Q. 2019. Surface Optimization of Ship Type Ditching System Based on Differential Geometry and EDEM Simulation. Trans. Chin. Soc. Agric. Machin. 8:59-69.
Lu H., Feng Y., Gao Q., Xing J., Chen Y., Yang L., Xue L. 2020. Surface soil mixing is more beneficial than the plough layer mixing mode of biochar application for nitrogen retention in a paddy system. Sci. Total Environ. 718:137399.
Lv J., Liu Q., Li Z., Li J., Liu Z. 2021. Design and Experiment of Soil Cultivating Device of Plowshare Potato Field Cultivator. Trans. Chin. Soc. Agric. Machin. 7:71-82.
Niu Q., Wang Q., Chen L., Li H., He J., Li W. 2017. Design and experiment on straw post-covering wheat planter. Trans. Chin. Soc. Agric. Machin. 48:52-9.
Shi L., Zhao W., Sun W. 2017. Parameter calibration of soil particles contact model of farmland soil in northwest arid region based on discrete element method. Trans. Chin. Soc. Agric. Eng. 33:181-7.
Sun K., Yu J., Liang L., Wang Y., Yan D., Zhou L., Yu Y. 2022. A DEM-based general modelling method and experimental verification for wheat seeds. Powder Technol. 401:117353.
Sun L., Gibson R.F., Gordaninejad F., Suhr J. 2009. Energy absorption capability of nanocomposites: a review. Compos. Sci. Technol. 69:2392-409.
Wang X., Hu H., Wang Q., Li H., He J., Chen W. 2017. Calibration Method of Soil Contact Characteristic Parameters Based on DEM Theory. Trans. Chin. Soc. Agric. Machin. 12:78-85.
Wei G., Zhang Q., Liu L., Xiao W., Sun W., Liao Q. 2020. Design and Experiment of Plowing and Rotary Tillage Buckle Device for Rapeseed Direct Seeder. Trans. Chin. Soc. Agric. Machin. 6:38-46.
Wu T., Huang W., Chen X., Ma X., Han Z., Pan T. 2017. Calibration of discrete element model parameters for cohesive soil considering the cohesion between particles. J. South Chin. Agric. Univ. 38:93-8.
Xiong P., Yang Z., Sun Z., Zhang Q., Huang Y., Zhang Z. 2018. Simulation analysis and experiment for three-axis working resistances of rotary blade based on discrete element method. Trans. Chin. Soc. Agric. Eng. 18:113-21.
Yu J., Lu C., Wei R., Fu X., Li K., Tang Z., Wang F. 2018. Simulation test of performance of wheat precision seed-metering device based on Discrete Element Method. Jiangsu Agric. Sci. 8:225-8.
Zhai L. 2011. Study on the effects of plough’s working and structure parameters on its resistance under rheological soil conditions. PH.D. Nanjing Agric. Univ. Chin.
Zhang K., Huang J., Yang M., Zhang F., Huang X., Zhao C. 2010. Finite element analysis and experimental verification of wheat grain under compression loads. Trans. Chin. Soc. Agric. Eng. 6:352-6+391.
Zhang R., Li J., Li Y., Liu Z., Chen B. 2009. DEM macroscopic and mesoscopic analysis in disturbed behavior of soil acted by part with complex surface. J. Jilin Univ. Eng. Technol. Ed. 5:1218-23.
Zhang T., Liu F., Zhao M., Ma Q., Wang W., Fan Q., Yan P. 2018. Determination of corn stalk contact parameters and calibration of Discrete Element Method simulation. J. Chin. Agric. Univ. 4:120-7.
Zhang Z., He J., Li H., Wang Q., Ju J., Yan X. 2017. Design and Experiment on Straw Chopper Cum Spreader with Adjustable Spreading Device. Trans. Chin. Soc. Agric. Machin. 9:76-87.
Zhao H., He J., Li H., Liu C., Zheng K., Zhang Z. 2018a. Design and Experiment of Strip Rotary-cut-throw Anti-blocking Implement. Trans. Chin. Soc. Agric. Machin. 5:65-75.
Zhao H., He J., Li H., Mao Y., Liu P. 2018b. Comparison on soil, straw disturbance, and resistance of conventional and plainstraight blade for strip-tillage with Discrete Element Method. Int. Agric. Eng. J. 27:229-40.
Zhao L., Zhang Z., Wang C., Jian S., Liu T., Cui D., Ding X. 2018c. Design of monitoring system for wheat precision seeding-fertilizing machine based on variable distance photoelectric sensor. Trans. Chin. Soc. Agric. Eng. 13:27-34.
Zhao H., He J., Zheng Z., Zhang Z., Liu W. 2020. Strip Tillage Inter-row Residue Side-throwing Device of No/minimum till Seeder for Anti-blocking and Seedbed-cleaning. Trans. Chin. Soc. Agric. Machin. 12:24-34.
Zhao S., Liu H., Yang C., Yang L., Gao L., Yang Y. 2021. Design and Discrete Element Simulation of Interactive Layered Subsoiler with Maize Straw Returned to Filed. Trans. Chin. Soc. Agric. Machin. 3:75-87.
Zhao S., Wang J., Yang C., Chen J., Yang, Y. 2019. Design and Experiment of Stubble Chopper under Conservation Tillage. Trans. Chin. Soc. Agric. Machin. 9:57-68.
Zhong X., Zhang X., Geng Y., Wei Z., Cheng X., Wang X. 2023. Research on Load Transfer of Straw-soil Complex Based on Discrete Element Method. J. Agric. Mechan. Res. 3:17-24.
How to Cite
Liu, L. (2023) “Design and experiment of furrow side pick-up soil blade for wheat strip-till planter using the discrete element method”, Journal of Agricultural Engineering, 55(1). doi: 10.4081/jae.2023.1546.
Copyright (c) 2023 the Author(s)
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
PAGEPress has chosen to apply the Creative Commons Attribution NonCommercial 4.0 International License (CC BY-NC 4.0) to all manuscripts to be published.
Similar Articles
- Luhua Han, Haorui Ma, Menghan Mo, Francis Kumi, Jianping Hu, Hanping Mao, Design and test of an efficient seedling pick-up device with a combination of air jet ejection and mechanical action , Journal of Agricultural Engineering: Vol. 55 No. 3 (2024)
- Volodymyr Bulgakov, Valerii Adamchuk, Ladislav Nozdrovicky, Ivan Holovach, Theory of the interaction of flat sensing organ with the head of the sugar beet root , Journal of Agricultural Engineering: Vol. 48 No. 4 (2017)
- Angelo Fabbri, Chiara Cevoli, Giuseppe Cantalupo, A method for handlebars ballast calculation in order to reduce vibrations transmissibility in walk behind tractors , Journal of Agricultural Engineering: Vol. 48 No. 2 (2017)
- Shinar Ospanova, Mubarak Aduov, Sultan Kapov, Alexander Orlyansky, Kadirbek Volodya, The results of experimental research of a rotor seed-metering unit for sowing non-free-flowing seeds , Journal of Agricultural Engineering: Vol. 55 No. 1 (2024)
- Lingxin Bu, Qianwen Kou, Adilet Sugirbay, Jun Chen, Yu Chen, An air-assisted mechanical hill-seeding device for foxtail millet (Setaria italica) , Journal of Agricultural Engineering: Vol. 55 No. 2 (2024)
- Maria E. Menconi, David Grohmann, Piero Borghi, Dynamic thermal simulation on retrofitting scenarios for semi-extensive sheep farms , Journal of Agricultural Engineering: Vol. 45 No. 2 (2014)
- Ildar Badretdinov, Salavat Mudarisov, Eduard Khasanov, Ruslan Nasyrov, Marat Tuktarov, Operation technological process research in the cleaning system of the grain combine , Journal of Agricultural Engineering: Vol. 52 No. 2 (2021)
- Senanur Durgut Malçok, Azime Özkan Karabacak, Cüneyt Tunçkal, Canan Ece Tamer, Application of response surface methodology for optimisation of Cornelian cherry - Capia pepper leather dried in a heat pump drying system , Journal of Agricultural Engineering: Vol. 54 No. 3 (2023)
- Qinchao Xu, Shanjun Li, Haibing Pan, Qian Yang, Jian Zhang, Xuedong Lu, Cheng Shan, Design and operational parameters optimisation of a citrus substrate filling and transporting machine , Journal of Agricultural Engineering: Vol. 54 No. 3 (2023)
- Aristide Timene, Haman Djalo, Design of a five-bar duckbill-type mechanism for sorghum transplanting , Journal of Agricultural Engineering: Vol. 54 No. 2 (2023)
<< < 2 3 4 5 6 7 8 9 10 11 > >>
You may also start an advanced similarity search for this article.
