https://doi.org/10.4081/jae.2024.1685
Design of attitude-adjustable chassis and dynamic stress analysis of key components for crawler combine harvester
Published: 30 December 2024
Abstract Views: 39
PDF: 20
Publisher's note
All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article or claim that may be made by its manufacturer is not guaranteed or endorsed by the publisher.
All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article or claim that may be made by its manufacturer is not guaranteed or endorsed by the publisher.
Authors
To address the issues of leveling difficulties and poor stability of crawler combine harvesters in hilly and mountainous regions, this research analyzed the mechanical causes of overturning instability in crawler combine harvesters and designed an omnidirectional attitude adjustment chassis based on a five-bar mechanism. A 3D model was developed in SolidWorks, and coupled rigid-flexible simulations were performed using RecurDyn. Results showed that the chassis could achieve an overall lift, lateral adjustments and longitudinal adjustments (0-100 mm, -5.18° to 5.55° and -4.06° to 5.15° respectively), with maximum dynamic stress occurring on the left front and left rear rotational arms. A dynamic stress testing system was established to conduct response surface experiments. Field test results revealed that the primary factors affecting the maximum stress of the left front rotational arm were the grain tank loading mass, lateral adjustment angle, and longitudinal adjustment angle. For the left rear rotational arm, the order was the longitudinal adjustment angle, lateral adjustment angle, and grain tank loading mass. Validation tests showed that at a lateral adjustment angle of 3.61°, a longitudinal adjustment angle of 3.20°, and a grain tank load of 350 kg, the average maximum stresses were 483.19 MPa for the left front rotational arm and 188.95 MPa for the left rear rotational arm, with corresponding structural safety factors of 1.61 and 4.31, meeting strength requirements. This work provides methods for optimizing the design and reliability testing of agricultural machinery chassis with attitude adjustment functions in hilly terrains.
Adams, B., Darr, M. 2022. Validation principles of agricultural machine multibody dynamics models. J. ASABE 65:801-814.
DOI: https://doi.org/10.13031/ja.15045
Amirafshari, P., Brennan, F., Kolios, A. 2021. A fracture mechanics framework for optimising design and inspection of offshore wind turbine support structures against fatigue failure. Wind Energy Sci 6:677-699.
DOI: https://doi.org/10.5194/wes-6-677-2021
Belinsky, A., Ziganshin, B., Valiev, A., Haliullin, D., Galiev, I., Adigamov, N. 2019. Theoretical investigation of increasing efficiency of combine harvester operation on slopes. Eng.f Rural Develop. 18:206-213.
DOI: https://doi.org/10.22616/ERDev2019.18.N252
Chai, X., Hu, J., Ma, T., Liu, P., Shi, M., Zhu, L., Xu, L. 2024. Construction and characteristic analysis of dynamic stress coupling simulation models for the attitude-adjustable chassis of a combine harvester. Agronomy (Basel) 14:1874.
DOI: https://doi.org/10.3390/agronomy14081874
Jin, C., Yang, T., Liu, G., Wang, t., Chen, M., Liu, Z. 2020. Design and test of posture controlled chassis for caterpillar combine. Trans. CSAE 51:393-402.
Han, J., Kim, E., Moon, S., Lee, H., Kim, J., Park, Y. 2022. Fatigue integrity assessment for tractor-mounted garlic-onion harvester. J. Terramech. 100:1-10.
DOI: https://doi.org/10.1016/j.jterra.2021.11.005
Helian, B., Zheng, C., Bin, Y. 2021. Energy-saving and accurate motion control of a hydraulic actuator with uncertain negative loads. Chin. J. Aeronaut. 34:5:253-264.
DOI: https://doi.org/10.1016/j.cja.2020.12.025
Hu, J., Pan, J., Dai, B., Chai, X., Sun, Y., Xu, L. 2022. Development of an attitude adjustment crawler chassis for combine harvester and experiment of adaptive leveling system. Agronomy (Basel) 12:717.
DOI: https://doi.org/10.3390/agronomy12030717
İrsel, G., Altinbalik, M. T. 2018. Adaptation of tilt adjustment and tracking force automation system on a laser-controlled land leveling machine. Comput. Electron. Agric. 150:374-386.
DOI: https://doi.org/10.1016/j.compag.2018.04.021
Karliński, J., Stańco, M., Działak, P. 2023. The impact of the driving conditions on stress of load-bearing structure of self-propelled electric mining machine. Mater. Today Pro. 9: 791-798.
DOI: https://doi.org/10.1016/j.matpr.2023.07.137
Li, F., Liu, S., Mao, E., Du, Y., Lin, Y., Tian, J. 2016. Fatigue analysis of corn harvester frame based on power density. Trans. Chin. Soc. Agric. Eng. 32:34-40.
Lü, X., Liu, Z., Lü, X., Wang, X. 2024. Design and study on the leveling mechanism of the tractor body in hilly and mountainous areas. J. Eng. Design Technol. 22:679-689.
DOI: https://doi.org/10.1108/JEDT-11-2021-0617
Paul, A., Machavaram, R. 2024. Design of an adjustable chassis for a track type combine harvester. Cogent Eng. 11:2353811.
DOI: https://doi.org/10.1080/23311916.2024.2353811
Sirotin, P., Zhileykin, M., Sapegin, A., Zlenko, S. 2017. Prerequisites for the creation of an integrated system for leveling and cushioning framework of combine harvesters. Tract. Agr. Machin. 84: 21-28.
DOI: https://doi.org/10.17816/0321-4443-66335
Sun, J., Meng, C., Zhang, Y., Chu, G., Zhang, Y., Yang, F., Liu, Z. 2020. Design and physical model experiment of an attitude adjustment device for a crawler tractor in hilly and mountainous regions. Inform. Process. Agric. 7:466-478.
DOI: https://doi.org/10.1016/j.inpa.2020.02.004
Sun, Y., Xu, L., Jing, B., Chai, X., Li, Y. 2020. Development of a four-point adjustable lifting crawler chassis and experiments in a combine harvester. Comput. Electron. Agric. 173:105416.
DOI: https://doi.org/10.1016/j.compag.2020.105416
Si, D.Y., Fang, W.M., Zhang, Y. 2023. Flexible gear modeling and stress spectrum compilation of an artillery steering machine. J. Phys. Conf. Ser. 2528:012001.
DOI: https://doi.org/10.1088/1742-6596/2528/1/012001
Wang, Y., Yang, F., Pan, G., Liu, H., Liu, Z., Zhang, J. 2014. Design and testing of a small remote-control hillside tractor. J. ASABE 57:363-370.
DOI: https://doi.org/10.13031/trans.57.10229
Wang, Z., Ma, W., Wang, T., Liu, C. 2022. Body leveling control model establishment and experiment analysis. Appl. Eng. Agric. 38: 243-251.
DOI: https://doi.org/10.13031/aea.14501
Wang, Z., Xia, Y. 2019. Model establishment of body attitude adjustment system based on Backstepping control algorithm and automatic leveling technology. Cluster Comput. 22:14327-14337.
DOI: https://doi.org/10.1007/s10586-018-2292-y
Wang, Z., Yang, J., Liu, P., Long, X., Li, H., Wei, W. 2019. Development of an agricultural vehicle levelling system based on rapid active levelling. Biosyst. Eng. 186:337-348.
DOI: https://doi.org/10.1016/j.biosystemseng.2019.08.002
Wu, G., Wang, S., Zhang, A., Xiao, Y., Li, L., Yin, Y., Yan, B. 2023. Optimized design and experiment of a self-covering furrow opener for an automatic sweet potato seedling transplanting machine. Sustainability (Basel) 15:13091.
DOI: https://doi.org/10.3390/su151713091
Wang, C.J., Liu, Q., Yang, L. 2024. The MFBD-DEM coupling simulation approach for the investigation of granules screening effi-ciency in 4-DOF flip-flow screen. Granul. Matter. 26:5.
DOI: https://doi.org/10.1007/s10035-023-01380-5
Zhao, L.J., Yang, S.J., Zhang, H.N., Han, L.G. 2023. Fatigue life prediction of shearer rocker shell based on DEM-MFBD bidirectional coupling technology. Coal Sci. Tech. 51:S252-258.
Zhou, B., Chen, S., Hu, J., You, Y., Wang, D., Zhang, Q. 2024. Multi-body dynamics modeling and test of an articulated steering half-track tractor. Int. J. Agric. Biol. Eng. 16:124-133.
DOI: https://doi.org/10.25165/j.ijabe.20231606.8165
How to Cite
Hu, J. (2024) “Design of attitude-adjustable chassis and dynamic stress analysis of key components for crawler combine harvester”, Journal of Agricultural Engineering. doi: 10.4081/jae.2024.1685.
Copyright (c) 2024 the Author(s)
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
PAGEPress has chosen to apply the Creative Commons Attribution NonCommercial 4.0 International License (CC BY-NC 4.0) to all manuscripts to be published.
Similar Articles
- Piernicola Masella, Lorenzo Guerrini, Alessandro Parenti, Fabio Baldi, Paolo Spugnoli, Performance of a driven hitch-cart for draft animal power under different power take-off torque and ballast levels condition , Journal of Agricultural Engineering: Vol. 47 No. 4 (2016)
- Sara Cucchiaro, Laura Carretta, Paolo Nasta, Federico Cazorzi, Roberta Masin, Nunzio Romano, Paolo Tarolli, Multi-temporal geomorphometric analysis to assess soil erosion under different tillage practices: A methodological case study , Journal of Agricultural Engineering: Vol. 53 No. 1 (2022)
- Alessio Cislaghi, Gian Battista Bischetti, Best practices in post-flood surveys: The study case of Pioverna torrent , Journal of Agricultural Engineering: Vol. 53 No. 2 (2022)
- Simone Pascuzzi, The effects of the forward speed and air volume of an air-assisted sprayer on spray deposition in tendone trained vineyards , Journal of Agricultural Engineering: Vol. 44 No. 3 (2013)
- Daniele Masseroni, Jasim Uddin, Reece Tyrrell, Iven Mareels, Claudio Gandolfi, Arianna Facchi, Towards a smart automated surface irrigation management in rice-growing areas in Italy , Journal of Agricultural Engineering: Vol. 48 No. 1 (2017)
- Maria Lucia V. de Chiara, Maria Luisa Amodio, Francesco Scura, Luigina Spremulli, Giancarlo Colelli, Design and preliminary test of a fluidised bed photoreactor for ethylene oxidation on mesoporous mixed SiO2/TiO2 nanocomposites under UV-A illumination , Journal of Agricultural Engineering: Vol. 45 No. 4 (2014)
- Salvatore Praticò, Raimondo Tripodi, Viviana Tirella, Salvatore Di Fazio, Francesco Barreca, Giuseppe Modica, Proposal of an integrated 3D architectural survey method for application in historic agri-food building analysis and representation , Journal of Agricultural Engineering: Vol. 54 No. 3 (2023)
- Gennaro Giametta, Bruno Bernardi, MECHANIZED HARVESTING TESTS PERFORMED BY GRAPE HARVESTERS IN SUPER INTENSIVE OLIVE ORCHARD CULTIVATION IN SPAIN , Journal of Agricultural Engineering: Vol. 40 No. 2 (2009)
- Daniela Vanella, Filippo Ferlito, Biagio Torrisi, Alessio Giuffrida, Salvatore Pappalardo, Daniela Saitta, Giuseppe Longo-Minnolo, Simona Consoli, Long-term monitoring of deficit irrigation regimes on citrus orchards in Sicily , Journal of Agricultural Engineering: Vol. 52 No. 4 (2021)
- Daniel Veal, Lutz Damerow, Peter Schulze Lammers, Michael Blanke, Kinematic model for mechanical apple blossom thinning , Journal of Agricultural Engineering: Vol. 55 No. 1 (2024)
<< < 11 12 13 14 15 16 17 18 19 20 > >>
You may also start an advanced similarity search for this article.
