https://doi.org/10.4081/jae.2024.1685
Design of attitude-adjustable chassis and dynamic stress analysis of key components for crawler combine harvester
Published: 30 December 2024
Abstract Views: 39
PDF: 16
Publisher's note
All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article or claim that may be made by its manufacturer is not guaranteed or endorsed by the publisher.
All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article or claim that may be made by its manufacturer is not guaranteed or endorsed by the publisher.
Authors
To address the issues of leveling difficulties and poor stability of crawler combine harvesters in hilly and mountainous regions, this research analyzed the mechanical causes of overturning instability in crawler combine harvesters and designed an omnidirectional attitude adjustment chassis based on a five-bar mechanism. A 3D model was developed in SolidWorks, and coupled rigid-flexible simulations were performed using RecurDyn. Results showed that the chassis could achieve an overall lift, lateral adjustments and longitudinal adjustments (0-100 mm, -5.18° to 5.55° and -4.06° to 5.15° respectively), with maximum dynamic stress occurring on the left front and left rear rotational arms. A dynamic stress testing system was established to conduct response surface experiments. Field test results revealed that the primary factors affecting the maximum stress of the left front rotational arm were the grain tank loading mass, lateral adjustment angle, and longitudinal adjustment angle. For the left rear rotational arm, the order was the longitudinal adjustment angle, lateral adjustment angle, and grain tank loading mass. Validation tests showed that at a lateral adjustment angle of 3.61°, a longitudinal adjustment angle of 3.20°, and a grain tank load of 350 kg, the average maximum stresses were 483.19 MPa for the left front rotational arm and 188.95 MPa for the left rear rotational arm, with corresponding structural safety factors of 1.61 and 4.31, meeting strength requirements. This work provides methods for optimizing the design and reliability testing of agricultural machinery chassis with attitude adjustment functions in hilly terrains.
Adams, B., Darr, M. 2022. Validation principles of agricultural machine multibody dynamics models. J. ASABE 65:801-814.
DOI: https://doi.org/10.13031/ja.15045
Amirafshari, P., Brennan, F., Kolios, A. 2021. A fracture mechanics framework for optimising design and inspection of offshore wind turbine support structures against fatigue failure. Wind Energy Sci 6:677-699.
DOI: https://doi.org/10.5194/wes-6-677-2021
Belinsky, A., Ziganshin, B., Valiev, A., Haliullin, D., Galiev, I., Adigamov, N. 2019. Theoretical investigation of increasing efficiency of combine harvester operation on slopes. Eng.f Rural Develop. 18:206-213.
DOI: https://doi.org/10.22616/ERDev2019.18.N252
Chai, X., Hu, J., Ma, T., Liu, P., Shi, M., Zhu, L., Xu, L. 2024. Construction and characteristic analysis of dynamic stress coupling simulation models for the attitude-adjustable chassis of a combine harvester. Agronomy (Basel) 14:1874.
DOI: https://doi.org/10.3390/agronomy14081874
Jin, C., Yang, T., Liu, G., Wang, t., Chen, M., Liu, Z. 2020. Design and test of posture controlled chassis for caterpillar combine. Trans. CSAE 51:393-402.
Han, J., Kim, E., Moon, S., Lee, H., Kim, J., Park, Y. 2022. Fatigue integrity assessment for tractor-mounted garlic-onion harvester. J. Terramech. 100:1-10.
DOI: https://doi.org/10.1016/j.jterra.2021.11.005
Helian, B., Zheng, C., Bin, Y. 2021. Energy-saving and accurate motion control of a hydraulic actuator with uncertain negative loads. Chin. J. Aeronaut. 34:5:253-264.
DOI: https://doi.org/10.1016/j.cja.2020.12.025
Hu, J., Pan, J., Dai, B., Chai, X., Sun, Y., Xu, L. 2022. Development of an attitude adjustment crawler chassis for combine harvester and experiment of adaptive leveling system. Agronomy (Basel) 12:717.
DOI: https://doi.org/10.3390/agronomy12030717
İrsel, G., Altinbalik, M. T. 2018. Adaptation of tilt adjustment and tracking force automation system on a laser-controlled land leveling machine. Comput. Electron. Agric. 150:374-386.
DOI: https://doi.org/10.1016/j.compag.2018.04.021
Karliński, J., Stańco, M., Działak, P. 2023. The impact of the driving conditions on stress of load-bearing structure of self-propelled electric mining machine. Mater. Today Pro. 9: 791-798.
DOI: https://doi.org/10.1016/j.matpr.2023.07.137
Li, F., Liu, S., Mao, E., Du, Y., Lin, Y., Tian, J. 2016. Fatigue analysis of corn harvester frame based on power density. Trans. Chin. Soc. Agric. Eng. 32:34-40.
Lü, X., Liu, Z., Lü, X., Wang, X. 2024. Design and study on the leveling mechanism of the tractor body in hilly and mountainous areas. J. Eng. Design Technol. 22:679-689.
DOI: https://doi.org/10.1108/JEDT-11-2021-0617
Paul, A., Machavaram, R. 2024. Design of an adjustable chassis for a track type combine harvester. Cogent Eng. 11:2353811.
DOI: https://doi.org/10.1080/23311916.2024.2353811
Sirotin, P., Zhileykin, M., Sapegin, A., Zlenko, S. 2017. Prerequisites for the creation of an integrated system for leveling and cushioning framework of combine harvesters. Tract. Agr. Machin. 84: 21-28.
DOI: https://doi.org/10.17816/0321-4443-66335
Sun, J., Meng, C., Zhang, Y., Chu, G., Zhang, Y., Yang, F., Liu, Z. 2020. Design and physical model experiment of an attitude adjustment device for a crawler tractor in hilly and mountainous regions. Inform. Process. Agric. 7:466-478.
DOI: https://doi.org/10.1016/j.inpa.2020.02.004
Sun, Y., Xu, L., Jing, B., Chai, X., Li, Y. 2020. Development of a four-point adjustable lifting crawler chassis and experiments in a combine harvester. Comput. Electron. Agric. 173:105416.
DOI: https://doi.org/10.1016/j.compag.2020.105416
Si, D.Y., Fang, W.M., Zhang, Y. 2023. Flexible gear modeling and stress spectrum compilation of an artillery steering machine. J. Phys. Conf. Ser. 2528:012001.
DOI: https://doi.org/10.1088/1742-6596/2528/1/012001
Wang, Y., Yang, F., Pan, G., Liu, H., Liu, Z., Zhang, J. 2014. Design and testing of a small remote-control hillside tractor. J. ASABE 57:363-370.
DOI: https://doi.org/10.13031/trans.57.10229
Wang, Z., Ma, W., Wang, T., Liu, C. 2022. Body leveling control model establishment and experiment analysis. Appl. Eng. Agric. 38: 243-251.
DOI: https://doi.org/10.13031/aea.14501
Wang, Z., Xia, Y. 2019. Model establishment of body attitude adjustment system based on Backstepping control algorithm and automatic leveling technology. Cluster Comput. 22:14327-14337.
DOI: https://doi.org/10.1007/s10586-018-2292-y
Wang, Z., Yang, J., Liu, P., Long, X., Li, H., Wei, W. 2019. Development of an agricultural vehicle levelling system based on rapid active levelling. Biosyst. Eng. 186:337-348.
DOI: https://doi.org/10.1016/j.biosystemseng.2019.08.002
Wu, G., Wang, S., Zhang, A., Xiao, Y., Li, L., Yin, Y., Yan, B. 2023. Optimized design and experiment of a self-covering furrow opener for an automatic sweet potato seedling transplanting machine. Sustainability (Basel) 15:13091.
DOI: https://doi.org/10.3390/su151713091
Wang, C.J., Liu, Q., Yang, L. 2024. The MFBD-DEM coupling simulation approach for the investigation of granules screening effi-ciency in 4-DOF flip-flow screen. Granul. Matter. 26:5.
DOI: https://doi.org/10.1007/s10035-023-01380-5
Zhao, L.J., Yang, S.J., Zhang, H.N., Han, L.G. 2023. Fatigue life prediction of shearer rocker shell based on DEM-MFBD bidirectional coupling technology. Coal Sci. Tech. 51:S252-258.
Zhou, B., Chen, S., Hu, J., You, Y., Wang, D., Zhang, Q. 2024. Multi-body dynamics modeling and test of an articulated steering half-track tractor. Int. J. Agric. Biol. Eng. 16:124-133.
DOI: https://doi.org/10.25165/j.ijabe.20231606.8165
How to Cite
Hu, J. (2024) “Design of attitude-adjustable chassis and dynamic stress analysis of key components for crawler combine harvester”, Journal of Agricultural Engineering. doi: 10.4081/jae.2024.1685.
Copyright (c) 2024 the Author(s)
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
PAGEPress has chosen to apply the Creative Commons Attribution NonCommercial 4.0 International License (CC BY-NC 4.0) to all manuscripts to be published.
Similar Articles
- Ugo Lazzaro, Caterina Mazzitelli, Benedetto Sica, Paola Di Fiore, Nunzio Romano, Paolo Nasta, On evaluating the hypothesis of shape similarity between soil particle-size distribution and water retention function , Journal of Agricultural Engineering: Vol. 54 No. 4 (2023)
- Angelo Fabbri, Chiara Cevoli, Florina Aurelia Silaghi, Adriano Guarnieri, NUMERICAL SIMULATION OF PHYSICAL SYSTEMS IN AGRI-FOOD ENGINEERING , Journal of Agricultural Engineering: Vol. 42 No. 4 (2011)
- Alberto Finzi, Elisabetta Riva, Alda Bicoku, Viviana Guido, Seit Shallari, Giorgio Provolo, Comparison of techniques for ammonia emission mitigation during storage of livestock manure and assessment of their effect in the management chain , Journal of Agricultural Engineering: Vol. 50 No. 1 (2019)
- José Roberto Moreira Ribeiro Gonçalves, Gabriel Araújo e Silva Ferraz, Étore Francisco Reynaldo, Diego Bedin Marin, Patrícia Ferreira Ponciano Ferraz, Manuel Pérez-Ruiz, Giuseppe Rossi, Marco Vieri, Daniele Sarri, Comparative analysis of soil-sampling methods used in precision agriculture , Journal of Agricultural Engineering: Vol. 52 No. 1 (2021)
- Celeste Righi Ricco, Alberto Finzi, Viviana Guido, Elisabetta Riva, Omar Ferrari, Giorgio Provolo , Evaluation of ammonia emissions from filtration of digestate used for fertigation , Journal of Agricultural Engineering: Vol. 52 No. 3 (2021)
- Fernando Ferreira Abreu, Luiz Henrique Antunes Rodrigues, Monitoring mini-tomatoes growth: A non-destructive machine vision-based alternative , Journal of Agricultural Engineering: Vol. 53 No. 3 (2022)
- Bing Li, Jiyun Li, Key technology of crop precision sowing based on the vision principle , Journal of Agricultural Engineering: Vol. 54 No. 1 (2023)
- Manuela Mancini, Elena Leoni, Michela Nocetti, Carlo Urbinati, Daniele Duca, Michele Brunetti, Giuseppe Toscano, Near infrared spectroscopy for assessing mechanical properties of Castanea sativa wood samples , Journal of Agricultural Engineering: Vol. 50 No. 4 (2019)
- Fabiana Convertino, Ileana Blanco, Evelia Schettini, Giuliano Vox, A nature-based system for improving Mediterranean buildings’ performance: contribution to energy saving by heat transfer reduction and influence of climatic parameters , Journal of Agricultural Engineering: Vol. 54 No. 3 (2023)
- George Ashwehmbom Looh, Fangping Xie, Xiushan Wang, Augustine Ngiejungbwen Looh, Hamdaoui Hind, Grain kernel damage during threshing: a comprehensive review of theories and models , Journal of Agricultural Engineering: Early Access
<< < 24 25 26 27 28 29 30 31 32 > >>
You may also start an advanced similarity search for this article.
